A question, which is the Sakura Kasugano more popular out there?? I think it's POTS one, but I'm not sure if there's another one more famous than that, maybe an edit or with another style (SFA, MSHvSF, KOF, edited, etc)

Come here and kiss me, tubby

I wouldn't have known either. Whenever I run 1.0 in 1280x960, the frame rate takes a nosedive, so I tend to not bother switching from 640x480 on that engine. Nonetheless, I was able to fix the flickering in 1.0's higher resolutions.

Your screenshots, clips and preview videos look hi-res and have higher dimensions than mine. That's why it made me think it looks larger as the screenshots you take is like 2548x1914. Do you not use M.U.G.E.N itself to take the picture directly?

Revealed the 5th character of season 4.
nothing more nothing less than Goku

BURST SYSTEM OVERHAUL
-New Burst Icon that also turns red when Not Over Yet is active.
-Burst now slowly regenerates overtime after use and does not fully regenerate between rounds.
-The rate of regeneration scales according to how much health has been lost.
-Burst meter is also gained on hit based on the amount of damage taken.
-When not over yet is active, the amount of meter gained is increased in both cases.

EXCEED ACCEL
-Triggered by pressing Y+Z when Ultra Burst is active.
-While it doesn't deal as much damage as most Distortion Drives, it has minimal damage scaling.
-Does not cost meter, but will immediately end Ultra Burst after use.
-Cannot be Rapid Canceled.
-Becomes upgraded when Not Over Yet is active.
-Holding down Y+Z during an Ultra Guard Cancel will immediately follow up with the Exceed Accel after the animation finishes.
-Hitting the opponent with an Exceed Accel will refill the Burst Gauge by 30% and will prevent the Burst Gauge from overheating.

OVERHEAT
-Burst gauge becomes overheated either when Ultra Burst runs out or if the Exceed Accel or Astral Heat is unsuccessful.
-An overheated burst gauge won't be able to regenerate for a set amount of time and will cause the power meter to slowly drain throughout the duration.
-Overheat is immediately removed between rounds.
-Astral Heat will not be available during Overheat even if you manage to have enough meter for it.

NEGATIVE PENALTY
-Performing too many consecutive back dashes or dodges will trigger a Negative Penalty, which immediately sets your meter and burst gauge to zero and puts you into overheat status.
-You will receive a warning before you get a Negative Penalty
-Moving toward and attacking the opponent will make the warning subside.

MISC
-Type Lumina style Super Jump. Heavier characters such as Blitztank have reduced distance on their super jumps. Triggered by tapping Down then Up in quick succession.
-A+B+Forward and A+B+Back are now macros for Double Tap Forward and Double Tap Backward respectively, Making instant air dashes easier to pull off.
-Significantly reduced knock back from a regular burst on block.
-Ultra Burst Cut-ins are no longer exclusive to the Persona cast.
-The base amount of time for Ultra Burst has been increased.
-Ultra Burst Timer will no longer increment during the initial Ultra Burst state.
-A successful Astral Heat will set the Burst Gauge to zero on the next round, assuming that the match isn't over.

I thought Portal Crawl was too hard to avoid until I figured out the pattern, or how I realized we should preserve our super meters to hit him out of Laser.

- Black Hole can't be escaped by characters without fast dashes, teleports, etc. I suggest making the vacuum weaker if P2 is mashing the back direction

- His round 2 Laser variation really got me good, hehe

;Black Hole Pull Strength
[State 5900, 1] 
type = Varset
trigger1 = 1
var(44) = 5
;This value determines how quickly the Black Hole attack will pull the opponent in
;Setting this to anything higher than 25 will likely cause unintended behavior
;Default value is 8

;Timer Toggle
[State 5900, 1] 
type = Varset
trigger1 = 1
var(45) = 1
;Setting this value to 0 will allow the timer to count down while fighting Marx
;The timer will still freeze when Marx has been reverted back to his original form 
;Default value is 1

;Attack Wait Time (Phase 1)
[State 5900, 1] 
type = Varset
trigger1 = 1
var(47) = 150 
;This value determines how much time in frames Marx waits between attacks when controlled by the AI
;60 frames is equal to 1 second
;Default value is 140

;Attack Wait Time (Phase 2)
[State 5900, 1] 
type = Varset
trigger1 = 1
var(48) = 150 
;Same as above, except this value applies after Marx has lost a round
;Default value is 90

;Laser Interruption Damage Threshold
[State 5900, 1] 
type = Varset
trigger1 = 1
var(49) = 200 
;This value determines how much damage needs to be dealt to Marx in order to interrupt his laser charge
;Default value is 400

GO YOU!

Quick question: Will you ever do more Smash boss characters in the future? Just like you made Marx

A little curious, when will you release the system update?

Spoiler: Coming soon. (click to see content)

Akiha infinite.

[State 5050, 4] ;Recover near ground
type = SelfState
triggerall = stateno = 6050
triggerall = Vel Y > 0
triggerall = Pos Y >= -20
triggerall = alive
triggerall = CanRecover
trigger1 = Command = "recovery"
trigger2 = var(16) = 1
trigger2 = var(23)>=var(22)
value = 5200 ;HITFALL_RECOVER

[State -2]; Recover in mid air
type = selfState
triggerall = stateno = 6050
triggerall = Vel Y > -1
triggerall = alive
triggerall = CanRecover
trigger1 = Command = "recovery"
trigger2 = var(16) = 1
trigger2 = var(23)>=var(22)
value = 5210 ;HITFALL_AIRRECOVER

Hey OHMSBY, where does this model of Marx come from? Did he come from Kirby All Star Allies(KASA) or Smash Ultimate? Can't tell because the his base form reminds me of how he looks in KASA, but his boss form looks like it could be from either Ultimate or KASA. Also how will this little guy play like? Will he fight normally until his health reaches a certain point and he turns into his boss form? Or will he start in his boss form and he'll then change into his regular when you do enough damage to him?

Spoiler: And my next character is... (click to see content)

I wouldn't have known about these debug errors if debug mode wasn't on. That's why it's so easy to miss these.

I too look forward who it is, but the only slight problem would be the sprites which I heard they are very large in file size (Even bigger than your SSBU renders in gigabytes) and need to be heavily compressed.